Use refactored LNBP21/BSBE1 code for Technotrend/Hauppauge DVB-S rev 2.3.
As a side effect, FE_ENABLE_HIGH_LNB_VOLTAGE ioctl is supported now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved duplicated code to separate files.
LNBP21 stuff rewritten from scratch, BSBE1 copied from av7110.c.
Modified budget driver to use the new routines.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Workaround for Nexus CA: Debi test fails unless first debi write is repeated.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- make 2 needlessly global functions static
- remove cpia2_setup(): the driver already allows setting parameters
through module_param(), and there's no reason for having two different
ways for setting the same parameters
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved keymaps to the ir-common module, and export them from there, instead
of #including them in each module
Included missing files from V4L/DVB(3197).
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- ELSA EX-VISION 500TV was incorrectly programmed to have the same
subsystem ID as ELSA EX-VISION 300TV, (1048:226b)
- This changeset replaces the incorrect subsystem ID (1048:226b)
with the correct one (1048:226a) for the ELSA EX-VISION 500TV.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fixed tda9886 port 2 setting
- turned remote control receiver off via saa7134 GPIO to avoid i2c hangs
- modified tda9886 client calls to direct i2c access to allow proper return
to analog mode
- allow mode change to V4L2_TUNER_DIGITAL_TV in tuner VIDIOC_S_FREQUENCY
client call
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the strange crashes I was seeing after using
bttv card, caused by a buffer overflow in bttv_risc_packed.
The instruction buffer size calculation contains two errors:
(a) a non-zero padding value can push the start of the next bpl
section to just before a page border, leading to more scanline
splits and thus additional instructions.
(b) the first DMA region can be smaller than one page, so there can
be a scanline split even if bpl*lines is smaller than PAGE_SIZE.
For example, consider the case where offset is 0, bpl is 2, padding
is 4094, lines is smaller than 2048, the first DMA region has size 1
and all others have size PAGE_SIZE, assumed to equal 4096. Then
all bpl regions cross page borders and the number of instructions
written is 2*lines+2, rather than lines+2 (the current estimate).
With this patch the number of instructions for this example is
estimated to be 2*lines+3.
Also, the BUG_ON that was supposed to catch buffer overflows contained
a thinko causing it fire only if the buffer was overrun by a factor of
16 or more, so it fixes the the BUG_ON's (using sizeof rather than "4").
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fix temporary debug code by changing printk to dprintk at level 1.
- move CORE_IOCTL messages from level 1 to level 2.
- this should help with selective debugging,
while not filling people's logs up during normal use.
Signed-off-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Current xc3028 support is still experimental, requiring more work to be
sent to mainstream. It will be kept only at mercurial tree on
http://linuxtv.org/hg until fixed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After a FIFO corruptions occurrs (generally due to buffer overflow), FIFO
contents needs to be discarted.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, root may change parameters while module is running.
Thanks to Edgar Toerning
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed broken IF-OUT on pinnacle sat board.
Thanks to Edgar Toernig
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ignore invalid messages on cx24110 frontend.
Thanks to Edgar Toernig
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The field "dvr" in struct dmxdev is competely unused. Remove
it and code which allocates, initializes and frees it.
Signed-off-by: Peter Beutner <p.beutner@gmx.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
use __devinit/__devexit/__devexit_p() where appropriate
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: Mattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The probing code for tda8290 changes the state of the tda9887 GP ports.
The patch assumes that if probing for tda8290 failed, this must be a
tda9887 and restores its power on defaults.
This should solve the module load order issue with some pinnacle cards.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There has been a CPIA2 driver out of kernel for a long time and it has
been pretty clean for some time too. This is an import of the
sourceforge driver which has been stripped of
- 2.4 back compatibility
- 2.4 old style MJPEG ioctls
A couple of functions have been made static and the docs have been
repackaged into Documentation/video4linux. The rvmalloc/free functions now
match the cpia driver again. Other than that this is the code as is.
Tested on x86-64 with a QX5 microscope.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add two new ioctls to read the 33 bit presentation time stamp from audio
and video devices as defined in ITU T-REC-H.222.0 and ISO/IEC 13818-1.
Acked-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously, only NTSC and PAL/M were associated to 30fps and
525 lines, so, PAL/60 were not handled properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added a new function that allows printing ioctl arguments.
This makes easier to include debug code under v4l ioctl
handling.
Also fixed some declarations on internal ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The remote controller on the LifeView FlyDVB-T Duo card work flawlessly
with the same settings as the LifeView FlyDVB-T LR301 card.
Signed-off-by: Rudo Thomas <rudo@matfyz.cz>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Standard video using the cx88 broadcast decoder is
working, but blackbird isn't working yet, audio is only
working correctly for television mode. S-Video and Composite
are working for video-only, so I have them disabled for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Enable the tuv1236 tuner on the Kworld-ATSC110 card so that the
tuner can be identified when tuners.ko loads.
- With this change it is no longer necessary to remove and reload
the tuner module in order to get the tuv1236 identified.
- This code was copied from the ATI HDTV Wonder init routine (in cx88-cards.c)
which also uses the TUV1236D.
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- There is no radio with this tuner card...
Thanks-to: Dwaine Garden <DwaineGarden@rogers.com>
- fixed capitalization in card name.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- When tuning VSB, use ANT input
- When tuning QAM, use CABLE input
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following are specific to lgdt3303, and are being renamed to reflect this.
- cxusb_lgdt330x_config renamed to cxusb_lgdt3303_config.
- cxusb_lgdt330x_frontend_attach renamed to cxusb_lgdt3303_frontend_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The remote control interface for this board is the same as the one for
BTTV_BOARD_CONCEPTRONIC_CTVFMI2
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When multiple cards were installed, only the first card would have
audio initialized, because only the first position in the array parameter
defaulted to "1"
To make things worse, the "enable" parameter wasn't enabled, so there
was no workaround.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds another composite input to the Pinnacle PCTV 100i
definition which filters the chrominace signal from the luma input. This
improves video quality for Composite signals on the S-Video connector of
the card.
In addition the name string of the card is changed to include PCTV 40i
and 50i since these cards are identical.
Signed-off-by: Karsten Suehring <ksuehring@gmx.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for ELSA EX-VISION 700TV, which is the ELSA Japan's
flagship model of the software encoding TV capture card.
All inputs (Television, Composite1 and S-Video) have been tested.
Signed-off-by: Tamuki Shoichi <tamuki@linet.gr.jp>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- add radio support for KWorld HardwareMpegTV XPert
- fix GPIO settings for tv and radio
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
to remove some code duplication
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
