1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
82 lines
2.5 KiB
Plaintext
82 lines
2.5 KiB
Plaintext
#
|
|
# FC4 device configuration
|
|
#
|
|
|
|
menu "Fibre Channel support"
|
|
|
|
config FC4
|
|
tristate "Fibre Channel and FC4 SCSI support"
|
|
---help---
|
|
Fibre Channel is a high speed serial protocol mainly used to
|
|
connect large storage devices to the computer; it is compatible with
|
|
and intended to replace SCSI.
|
|
|
|
This is an experimental support for storage arrays connected to your
|
|
computer using optical fibre cables and the "X3.269-199X Fibre
|
|
Channel Protocol for SCSI" specification. If you want to use this,
|
|
you need to say Y here and to "SCSI support" as well as to the
|
|
drivers for the storage array itself and for the interface adapter
|
|
such as SOC or SOC+. This subsystem could even serve for IP
|
|
networking, with some code extensions.
|
|
|
|
If unsure, say N.
|
|
|
|
comment "FC4 drivers"
|
|
depends on FC4
|
|
|
|
config FC4_SOC
|
|
tristate "Sun SOC/Sbus"
|
|
depends on FC4!=n && (SPARC32 || SPARC64)
|
|
help
|
|
Serial Optical Channel is an interface card with one or two Fibre
|
|
Optic ports, each of which can be connected to a disk array. Note
|
|
that if you have older firmware in the card, you'll need the
|
|
microcode from the Solaris driver to make it work.
|
|
|
|
To compile this support as a module, choose M here: the module will
|
|
be called soc.
|
|
|
|
config FC4_SOCAL
|
|
tristate "Sun SOC+ (aka SOCAL)"
|
|
depends on FC4!=n && (SPARC32 || SPARC64)
|
|
---help---
|
|
Serial Optical Channel Plus is an interface card with up to two
|
|
Fibre Optic ports. This card supports FC Arbitrated Loop (usually
|
|
A5000 or internal FC disks in E[3-6]000 machines through the
|
|
Interface Board). You'll probably need the microcode from the
|
|
Solaris driver to make it work.
|
|
|
|
To compile this support as a module, choose M here: the module will
|
|
be called socal.
|
|
|
|
comment "FC4 targets"
|
|
depends on FC4
|
|
|
|
config SCSI_PLUTO
|
|
tristate "SparcSTORAGE Array 100 and 200 series"
|
|
depends on FC4!=n && SCSI
|
|
help
|
|
If you never bought a disk array made by Sun, go with N.
|
|
|
|
To compile this support as a module, choose M here: the module will
|
|
be called pluto.
|
|
|
|
config SCSI_FCAL
|
|
tristate "Sun Enterprise Network Array (A5000 and EX500)" if SPARC32 || SPARC64
|
|
depends on FC4!=n && SCSI
|
|
help
|
|
This driver drives FC-AL disks connected through a Fibre Channel
|
|
card using the drivers/fc4 layer (currently only SOCAL). The most
|
|
common is either A5000 array or internal disks in E[3-6]000
|
|
machines.
|
|
|
|
To compile this support as a module, choose M here: the module will
|
|
be called fcal.
|
|
|
|
config SCSI_FCAL
|
|
prompt "Generic FC-AL disk driver"
|
|
depends on FC4!=n && SCSI && !SPARC32 && !SPARC64
|
|
|
|
endmenu
|
|
|