kernel-aes67/drivers/net/sis900.h
Daniele Venzano ea37ccea66 [PATCH] Add Wake on LAN support to sis900 (2)
Sorry, but that day I had smoked somthing too heavy for me, the patch
didn't apply. Here's a new one.

The patch availble below adds support for Wake on LAN to the sis900
driver. Some register addresses were added to sis900.h and two new
functions were implemented in sis900.c. WoL status is controlled by
ethtool.
Patch is against 2.6.13.

Comments are welcome, but also consider for inclusion in the -mm series.

Signed-off-by: Daniele Venzano <venza@brownhat.org>

--
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-10-28 16:48:19 -04:00

325 lines
10 KiB
C

/* sis900.h Definitions for SiS ethernet controllers including 7014/7016 and 900
* Copyright 1999 Silicon Integrated System Corporation
* References:
* SiS 7016 Fast Ethernet PCI Bus 10/100 Mbps LAN Controller with OnNow Support,
* preliminary Rev. 1.0 Jan. 14, 1998
* SiS 900 Fast Ethernet PCI Bus 10/100 Mbps LAN Single Chip with OnNow Support,
* preliminary Rev. 1.0 Nov. 10, 1998
* SiS 7014 Single Chip 100BASE-TX/10BASE-T Physical Layer Solution,
* preliminary Rev. 1.0 Jan. 18, 1998
* http://www.sis.com.tw/support/databook.htm
*/
/*
* SiS 7016 and SiS 900 ethernet controller registers
*/
/* The I/O extent, SiS 900 needs 256 bytes of io address */
#define SIS900_TOTAL_SIZE 0x100
/* Symbolic offsets to registers. */
enum sis900_registers {
cr=0x0, //Command Register
cfg=0x4, //Configuration Register
mear=0x8, //EEPROM Access Register
ptscr=0xc, //PCI Test Control Register
isr=0x10, //Interrupt Status Register
imr=0x14, //Interrupt Mask Register
ier=0x18, //Interrupt Enable Register
epar=0x18, //Enhanced PHY Access Register
txdp=0x20, //Transmit Descriptor Pointer Register
txcfg=0x24, //Transmit Configuration Register
rxdp=0x30, //Receive Descriptor Pointer Register
rxcfg=0x34, //Receive Configuration Register
flctrl=0x38, //Flow Control Register
rxlen=0x3c, //Receive Packet Length Register
cfgpmcsr=0x44, //Configuration Power Management Control/Status Register
rfcr=0x48, //Receive Filter Control Register
rfdr=0x4C, //Receive Filter Data Register
pmctrl=0xB0, //Power Management Control Register
pmer=0xB4 //Power Management Wake-up Event Register
};
/* Symbolic names for bits in various registers */
enum sis900_command_register_bits {
RELOAD = 0x00000400, ACCESSMODE = 0x00000200,/* ET */
RESET = 0x00000100, SWI = 0x00000080, RxRESET = 0x00000020,
TxRESET = 0x00000010, RxDIS = 0x00000008, RxENA = 0x00000004,
TxDIS = 0x00000002, TxENA = 0x00000001
};
enum sis900_configuration_register_bits {
DESCRFMT = 0x00000100 /* 7016 specific */, REQALG = 0x00000080,
SB = 0x00000040, POW = 0x00000020, EXD = 0x00000010,
PESEL = 0x00000008, LPM = 0x00000004, BEM = 0x00000001,
/* 635 & 900B Specific */
RND_CNT = 0x00000400, FAIR_BACKOFF = 0x00000200,
EDB_MASTER_EN = 0x00002000
};
enum sis900_eeprom_access_reigster_bits {
MDC = 0x00000040, MDDIR = 0x00000020, MDIO = 0x00000010, /* 7016 specific */
EECS = 0x00000008, EECLK = 0x00000004, EEDO = 0x00000002,
EEDI = 0x00000001
};
enum sis900_interrupt_register_bits {
WKEVT = 0x10000000, TxPAUSEEND = 0x08000000, TxPAUSE = 0x04000000,
TxRCMP = 0x02000000, RxRCMP = 0x01000000, DPERR = 0x00800000,
SSERR = 0x00400000, RMABT = 0x00200000, RTABT = 0x00100000,
RxSOVR = 0x00010000, HIBERR = 0x00008000, SWINT = 0x00001000,
MIBINT = 0x00000800, TxURN = 0x00000400, TxIDLE = 0x00000200,
TxERR = 0x00000100, TxDESC = 0x00000080, TxOK = 0x00000040,
RxORN = 0x00000020, RxIDLE = 0x00000010, RxEARLY = 0x00000008,
RxERR = 0x00000004, RxDESC = 0x00000002, RxOK = 0x00000001
};
enum sis900_interrupt_enable_reigster_bits {
IE = 0x00000001
};
/* maximum dma burst for transmission and receive */
#define MAX_DMA_RANGE 7 /* actually 0 means MAXIMUM !! */
#define TxMXDMA_shift 20
#define RxMXDMA_shift 20
enum sis900_tx_rx_dma{
DMA_BURST_512 = 0, DMA_BURST_64 = 5
};
/* transmit FIFO thresholds */
#define TX_FILL_THRESH 16 /* 1/4 FIFO size */
#define TxFILLT_shift 8
#define TxDRNT_shift 0
#define TxDRNT_100 48 /* 3/4 FIFO size */
#define TxDRNT_10 16 /* 1/2 FIFO size */
enum sis900_transmit_config_register_bits {
TxCSI = 0x80000000, TxHBI = 0x40000000, TxMLB = 0x20000000,
TxATP = 0x10000000, TxIFG = 0x0C000000, TxFILLT = 0x00003F00,
TxDRNT = 0x0000003F
};
/* recevie FIFO thresholds */
#define RxDRNT_shift 1
#define RxDRNT_100 16 /* 1/2 FIFO size */
#define RxDRNT_10 24 /* 3/4 FIFO size */
enum sis900_reveive_config_register_bits {
RxAEP = 0x80000000, RxARP = 0x40000000, RxATX = 0x10000000,
RxAJAB = 0x08000000, RxDRNT = 0x0000007F
};
#define RFAA_shift 28
#define RFADDR_shift 16
enum sis900_receive_filter_control_register_bits {
RFEN = 0x80000000, RFAAB = 0x40000000, RFAAM = 0x20000000,
RFAAP = 0x10000000, RFPromiscuous = (RFAAB|RFAAM|RFAAP)
};
enum sis900_reveive_filter_data_mask {
RFDAT = 0x0000FFFF
};
/* EEPROM Addresses */
enum sis900_eeprom_address {
EEPROMSignature = 0x00, EEPROMVendorID = 0x02, EEPROMDeviceID = 0x03,
EEPROMMACAddr = 0x08, EEPROMChecksum = 0x0b
};
/* The EEPROM commands include the alway-set leading bit. Refer to NM93Cxx datasheet */
enum sis900_eeprom_command {
EEread = 0x0180, EEwrite = 0x0140, EEerase = 0x01C0,
EEwriteEnable = 0x0130, EEwriteDisable = 0x0100,
EEeraseAll = 0x0120, EEwriteAll = 0x0110,
EEaddrMask = 0x013F, EEcmdShift = 16
};
/* For SiS962 or SiS963, request the eeprom software access */
enum sis96x_eeprom_command {
EEREQ = 0x00000400, EEDONE = 0x00000200, EEGNT = 0x00000100
};
/* PCI Registers */
enum sis900_pci_registers {
CFGPMC = 0x40,
CFGPMCSR = 0x44
};
/* Power management capabilities bits */
enum sis900_cfgpmc_register_bits {
PMVER = 0x00070000,
DSI = 0x00100000,
PMESP = 0xf8000000
};
enum sis900_pmesp_bits {
PME_D0 = 0x1,
PME_D1 = 0x2,
PME_D2 = 0x4,
PME_D3H = 0x8,
PME_D3C = 0x10
};
/* Power management control/status bits */
enum sis900_cfgpmcsr_register_bits {
PMESTS = 0x00004000,
PME_EN = 0x00000100, // Power management enable
PWR_STA = 0x00000003 // Current power state
};
/* Wake-on-LAN support. */
enum sis900_power_management_control_register_bits {
LINKLOSS = 0x00000001,
LINKON = 0x00000002,
MAGICPKT = 0x00000400,
ALGORITHM = 0x00000800,
FRM1EN = 0x00100000,
FRM2EN = 0x00200000,
FRM3EN = 0x00400000,
FRM1ACS = 0x01000000,
FRM2ACS = 0x02000000,
FRM3ACS = 0x04000000,
WAKEALL = 0x40000000,
GATECLK = 0x80000000
};
/* Management Data I/O (mdio) frame */
#define MIIread 0x6000
#define MIIwrite 0x5002
#define MIIpmdShift 7
#define MIIregShift 2
#define MIIcmdLen 16
#define MIIcmdShift 16
/* Buffer Descriptor Status*/
enum sis900_buffer_status {
OWN = 0x80000000, MORE = 0x40000000, INTR = 0x20000000,
SUPCRC = 0x10000000, INCCRC = 0x10000000,
OK = 0x08000000, DSIZE = 0x00000FFF
};
/* Status for TX Buffers */
enum sis900_tx_buffer_status {
ABORT = 0x04000000, UNDERRUN = 0x02000000, NOCARRIER = 0x01000000,
DEFERD = 0x00800000, EXCDEFER = 0x00400000, OWCOLL = 0x00200000,
EXCCOLL = 0x00100000, COLCNT = 0x000F0000
};
enum sis900_rx_bufer_status {
OVERRUN = 0x02000000, DEST = 0x00800000, BCAST = 0x01800000,
MCAST = 0x01000000, UNIMATCH = 0x00800000, TOOLONG = 0x00400000,
RUNT = 0x00200000, RXISERR = 0x00100000, CRCERR = 0x00080000,
FAERR = 0x00040000, LOOPBK = 0x00020000, RXCOL = 0x00010000
};
/* MII register offsets */
enum mii_registers {
MII_CONTROL = 0x0000, MII_STATUS = 0x0001, MII_PHY_ID0 = 0x0002,
MII_PHY_ID1 = 0x0003, MII_ANADV = 0x0004, MII_ANLPAR = 0x0005,
MII_ANEXT = 0x0006
};
/* mii registers specific to SiS 900 */
enum sis_mii_registers {
MII_CONFIG1 = 0x0010, MII_CONFIG2 = 0x0011, MII_STSOUT = 0x0012,
MII_MASK = 0x0013, MII_RESV = 0x0014
};
/* mii registers specific to ICS 1893 */
enum ics_mii_registers {
MII_EXTCTRL = 0x0010, MII_QPDSTS = 0x0011, MII_10BTOP = 0x0012,
MII_EXTCTRL2 = 0x0013
};
/* mii registers specific to AMD 79C901 */
enum amd_mii_registers {
MII_STATUS_SUMMARY = 0x0018
};
/* MII Control register bit definitions. */
enum mii_control_register_bits {
MII_CNTL_FDX = 0x0100, MII_CNTL_RST_AUTO = 0x0200,
MII_CNTL_ISOLATE = 0x0400, MII_CNTL_PWRDWN = 0x0800,
MII_CNTL_AUTO = 0x1000, MII_CNTL_SPEED = 0x2000,
MII_CNTL_LPBK = 0x4000, MII_CNTL_RESET = 0x8000
};
/* MII Status register bit */
enum mii_status_register_bits {
MII_STAT_EXT = 0x0001, MII_STAT_JAB = 0x0002,
MII_STAT_LINK = 0x0004, MII_STAT_CAN_AUTO = 0x0008,
MII_STAT_FAULT = 0x0010, MII_STAT_AUTO_DONE = 0x0020,
MII_STAT_CAN_T = 0x0800, MII_STAT_CAN_T_FDX = 0x1000,
MII_STAT_CAN_TX = 0x2000, MII_STAT_CAN_TX_FDX = 0x4000,
MII_STAT_CAN_T4 = 0x8000
};
#define MII_ID1_OUI_LO 0xFC00 /* low bits of OUI mask */
#define MII_ID1_MODEL 0x03F0 /* model number */
#define MII_ID1_REV 0x000F /* model number */
/* MII NWAY Register Bits ...
valid for the ANAR (Auto-Negotiation Advertisement) and
ANLPAR (Auto-Negotiation Link Partner) registers */
enum mii_nway_register_bits {
MII_NWAY_NODE_SEL = 0x001f, MII_NWAY_CSMA_CD = 0x0001,
MII_NWAY_T = 0x0020, MII_NWAY_T_FDX = 0x0040,
MII_NWAY_TX = 0x0080, MII_NWAY_TX_FDX = 0x0100,
MII_NWAY_T4 = 0x0200, MII_NWAY_PAUSE = 0x0400,
MII_NWAY_RF = 0x2000, MII_NWAY_ACK = 0x4000,
MII_NWAY_NP = 0x8000
};
enum mii_stsout_register_bits {
MII_STSOUT_LINK_FAIL = 0x4000,
MII_STSOUT_SPD = 0x0080, MII_STSOUT_DPLX = 0x0040
};
enum mii_stsics_register_bits {
MII_STSICS_SPD = 0x8000, MII_STSICS_DPLX = 0x4000,
MII_STSICS_LINKSTS = 0x0001
};
enum mii_stssum_register_bits {
MII_STSSUM_LINK = 0x0008, MII_STSSUM_DPLX = 0x0004,
MII_STSSUM_AUTO = 0x0002, MII_STSSUM_SPD = 0x0001
};
enum sis900_revision_id {
SIS630A_900_REV = 0x80, SIS630E_900_REV = 0x81,
SIS630S_900_REV = 0x82, SIS630EA1_900_REV = 0x83,
SIS630ET_900_REV = 0x84, SIS635A_900_REV = 0x90,
SIS96x_900_REV = 0X91, SIS900B_900_REV = 0x03
};
enum sis630_revision_id {
SIS630A0 = 0x00, SIS630A1 = 0x01,
SIS630B0 = 0x10, SIS630B1 = 0x11
};
#define FDX_CAPABLE_DUPLEX_UNKNOWN 0
#define FDX_CAPABLE_HALF_SELECTED 1
#define FDX_CAPABLE_FULL_SELECTED 2
#define HW_SPEED_UNCONFIG 0
#define HW_SPEED_HOME 1
#define HW_SPEED_10_MBPS 10
#define HW_SPEED_100_MBPS 100
#define HW_SPEED_DEFAULT (HW_SPEED_100_MBPS)
#define CRC_SIZE 4
#define MAC_HEADER_SIZE 14
#define TX_BUF_SIZE 1536
#define RX_BUF_SIZE 1536
#define NUM_TX_DESC 16 /* Number of Tx descriptor registers. */
#define NUM_RX_DESC 16 /* Number of Rx descriptor registers. */
#define TX_TOTAL_SIZE NUM_TX_DESC*sizeof(BufferDesc)
#define RX_TOTAL_SIZE NUM_RX_DESC*sizeof(BufferDesc)
/* PCI stuff, should be move to pci.h */
#define SIS630_VENDOR_ID 0x1039
#define SIS630_DEVICE_ID 0x0630