Because of rounding, in certain conditions, i.e. when in congestion
avoidance state rho is smaller than 1/128 of the current cwnd, TCP
Hybla congestion control starves and the cwnd is kept constant
forever.
This patch forces an increment by one segment after #send_cwnd calls
without increments(newreno behavior).
Signed-off-by: Daniele Lacamera <root@danielinux.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery tracked down a bug that explains many instances
of the error
unregister_netdevice: waiting for %s to become free. Usage count = %d
It turns out that netdev_run_todo can dead-lock with itself if
a second instance of it is run in a thread that will then free
a reference to the device waited on by the first instance.
The problem is really quite silly. We were trying to create
parallelism where none was required. As netdev_run_todo always
follows a RTNL section, and that todo tasks can only be added
with the RTNL held, by definition you should only need to wait
for the very ones that you've added and be done with it.
There is no need for a second mutex or spinlock.
This is exactly what the following patch does.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Ali Saidi <saidi@engin.umich.edu>
When TCP receive copy offload is enabled it's possible that
tcp_rcv_established() will cause two acks to be sent for a single
packet. In the case that a tcp_dma_early_copy() is successful,
copied_early is set to true which causes tcp_cleanup_rbuf() to be
called early which can send an ack. Further along in
tcp_rcv_established(), __tcp_ack_snd_check() is called and will
schedule a delayed ACK. If no packets are processed before the delayed
ack timer expires the packet will be acked twice.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer <hawk@comx.dk> reported a bug when setting a VLAN
device down that is in promiscous mode:
When the VLAN device is set down, the promiscous count on the real
device is decremented by one by vlan_dev_stop(). When removing the
promiscous flag from the VLAN device afterwards, the promiscous
count on the real device is decremented a second time by the
vlan_change_rx_flags() callback.
The root cause for this is that the ->change_rx_flags() callback is
invoked while the device is down. The synchronization is meant to mirror
the behaviour of the ->set_rx_mode callbacks, meaning the ->open function
is responsible for doing a full sync on open, the ->close() function is
responsible for doing full cleanup on ->stop() and ->change_rx_flags()
is meant to do incremental changes while the device is UP.
Only invoke ->change_rx_flags() while the device is UP to provide the
intended behaviour.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SLOB's ksize calculation was braindamaged and generally harmlessly
underreported the allocation size. But for very small buffers, it could
in fact overreport them, leading code depending on krealloc to overrun
the allocation and trample other data.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Tested-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 135aedc38e, as
requested by Hans Verkuil.
It was a patch for 2.6.28 where the BKL was pushed down from v4l core to
the drivers, not for 2.6.27!
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
* Theodore Ts'o (tytso@mit.edu) wrote:
>
> I've been playing with adding some markers into ext4 to see if they
> could be useful in solving some problems along with Systemtap. It
> appears, though, that as of 2.6.27-rc8, markers defined in code which is
> compiled directly into the kernel (i.e., not as modules) don't show up
> in Module.markers:
>
> kvm_trace_entryexit arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_entryexit arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
>
> (Note the lack of any of the kernel_sched_* markers, and the markers I
> added for ext4_* and jbd2_* are missing as wel.)
>
> Systemtap apparently depends on in-kernel trace_mark being recorded in
> Module.markers, and apparently it's been claimed that it used to be
> there. Is this a bug in systemtap, or in how Module.markers is getting
> built? And is there a file that contains the equivalent information
> for markers located in non-modules code?
I think the problem comes from "markers: fix duplicate modpost entry"
(commit d35cb360c2)
Especially :
- add_marker(mod, marker, fmt);
+ if (!mod->skip)
+ add_marker(mod, marker, fmt);
}
return;
fail:
Here is a fix that should take care if this problem.
Thanks for the bug report!
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Tested-by: "Theodore Ts'o" <tytso@mit.edu>
CC: Greg KH <greg@kroah.com>
CC: David Smith <dsmith@redhat.com>
CC: Roland McGrath <roland@redhat.com>
CC: Sam Ravnborg <sam@ravnborg.org>
CC: Wenji Huang <wenji.huang@oracle.com>
CC: Takashi Nishiie <t-nishiie@np.css.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: gart iommu have direct mapping when agp is present too
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: workaround for bogus gcc warning in ide_sysfs_register_port()
ide-cd: Optiarc DVD RW AD-7200A does play audio
IDE: Fix platform device registration in Swarm IDE driver (v2)
ide-dma: fix ide_build_dmatable() for TRM290
ide-cd: temporary tray close fix
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] IP27: Fix build errors if CONFIG_MAPPED_KERNEL=y
[MIPS] Fix CMP Kconfig configuration and mark as broken.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (33 commits)
V4L/DVB (9103): em28xx: HVR-900 B3C0 - fix audio clicking issue
V4L/DVB (9099): em28xx: Add detection for K-WORLD DVB-T 310U
V4L/DVB (9092): gspca: Bad init values for sonixj ov7660.
V4L/DVB (9080): gspca: Add a delay after writing to the sonixj sensors.
V4L/DVB (9075): gspca: Bad check of returned status in i2c_read() spca561.
V4L/DVB (9053): fix buffer overflow in uvc-video
V4L/DVB (9043): S5H1420: Fix size of shadow-array to avoid overflow
V4L/DVB (9037): Fix support for Hauppauge Nova-S SE
V4L/DVB (9029): Fix deadlock in demux code
V4L/DVB (8979): sms1xxx: Add new USB product ID for Hauppauge WinTV MiniStick
V4L/DVB (8978): sms1xxx: fix product name for Hauppauge WinTV MiniStick
V4L/DVB (8967): Use correct XC3028L firmware for AMD ATI TV Wonder 600
V4L/DVB (8963): s2255drv field count fix
V4L/DVB (8961): zr36067: Fix RGBR pixel format
V4L/DVB (8960): drivers/media/video/cafe_ccic.c needs mm.h
V4L/DVB (8958): zr36067: Return proper bytes-per-line value
V4L/DVB (8957): zr36067: Restore the default pixel format
V4L/DVB (8955): bttv: Prevent NULL pointer dereference in radio_open
V4L/DVB (8935): em28xx-cards: Remove duplicate entry (EM2800_BOARD_KWORLD_USB2800)
V4L/DVB (8933): gspca: Disable light frquency for zc3xx cs2102 Kokom.
...
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Reported-by: Hein_Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While debugging another bug it was found that NetRom socks
are sometimes seen unorphaned in sk_free(). This patch moves
sock_orphan() in nr_release() to the beginning (like in ax25,
or rose).
Reported-and-tested-by: Bernard Pidoux f6bvp <f6bvp@free.fr>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we reverted 30902dc3cb ("ax25: Fix
std timer socket destroy handling.") we have to put some kind of fix
in to cure the issue whereby unaccepted connections do not get destroyed.
The approach used here is from Tihomir Heidelberg - 9a4gl
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 30902dc3cb.
It causes all kinds of problems, based upon a report by
Bernard (f6bvp) and analysis by Jarek Poplawski.
Signed-off-by: David S. Miller <davem@davemloft.net>
The softlockup watchdog needs to be touched when resuming the from the
kgdb stopped state to avoid the printk that a CPU is stuck if the
debugger was active for longer than the softlockup threshold.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Stress-testing KVM's latest NMI support with kgdbts inside an SMP guest,
I came across spurious unhandled NMIs while running the singlestep test.
Looking closer at the code path each NMI takes when KGDB is enabled, I
noticed that kgdb_nmicallback is called twice per event: One time via
DIE_NMI_IPI notification, the second time on DIE_NMI. Removing the first
invocation cures the unhandled NMIs here.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
There is a bug in the BIOSes of some HP boxes with AMD Turions which
connects IO-APIC pins with ACPI thermal trip points in such a way that
if the state of the IO-APIC is not as expected by the (buggy) BIOS, the
thermal trip points are set to insanely low values (usually all of them
become 16 degrees Celsius). As a result, thermal throttling kicks in
and knock the system down to its shoes.
Unfortunately some of the recent IO-APIC changes made the bug show up.
To prevent this from happening, blacklist machines that are known to be
affected (nx6115 and 6715b in this particular case).
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=11516 listed as
a regression from 2.6.26.
On my box it was caused by:
commit 691874fa96
Author: Maciej W. Rozycki <macro@linux-mips.org>
Date: Tue May 27 21:19:51 2008 +0100
x86: I/O APIC: timer through 8259A second-chance
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
and the whole story is described in this (huge) thread:
http://marc.info/?l=linux-kernel&m=121358440508410&w=4
Matthew Garrett told us about that happening on the nx6125:
http://marc.info/?l=linux-kernel&m=121396307411930&w=4
and then Maciej analysed the breakage on the basis of a DSDT from the
nx6325:
http://marc.info/?l=linux-kernel&m=121401068718826&w=4
As far as the Dmitry's and Jason's boxes are concerned, I recognized the
symptoms and asked them to verify that the blacklisting helped.
It appears that the buggy BIOS code has been copy-pasted to the entire
range of machines, for no good reason.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Jason Vas Dias <jason.vas.dias@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new A-Link Bluetooth dongle is another one based on the BCM2046 chip
from Broadcom and it also needs to send HCI_Reset before it becomes fully
operational. Without the quirk it will show a lot of I/O errors.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Targus and Belkin have come out with new Bluetooth 2.1 capable dongles
using the latest BCM2046 chip from Broadcom. Both of them are so called
HID proxy dongles and they need to send HCI_Reset before they become
fully operational.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The transfer buffer of an URB will be automatically freed when using
the URB_FREE_BUFFER transfer_flag. So the extra calls to kfree() will
cause a double free.
Reported-by: Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Optiarc DVD RW AD-7200A can play audio, but tells it could not.
Signed-off-by: Bodo Eggert <7eggert@gmx.de>
Tested-by: Nick Warne <nick@ukfsn.org>
Received-from: Borislav Petkov <petkovbb@googlemail.com>
[bart: keep "audio" quirks together]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable. The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently, 'xcount' being 0 does not mean 0 bytes for TRM290; it means 4 bytes,
judging from the code immediately preceding this check. So, we must never try
to "split" the PRD for TRM290.
This is probably never hit anyway -- with the DMA buffers aligned to at least
512 bytes and ATAPI DMA not being used for non block I/O commands...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=11602.
A more generic fix for drives which cannot autoclose tray will follow.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
[bart: add an extra parentheses for consistency with the rest of kernel code]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
move init_memory_mapping() out of init_k8_gatt.
for: http://bugzilla.kernel.org/show_bug.cgi?id=11676
2.6.27-rc2 to rc8, apgart fails, iommu=soft works, regression
This is needed because we need to map the GART aperture even
if the GATT is not initialized.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fixed audio clicking problem which could be heard when using analog tv or composite input
Signed-off-by: Wiktor Grebla <greblus@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct firmware type to MTS
Correct audio routing for composite/s-video
Add DVB-T detection.
This patch uses the eeprom hash method for detection as the vendor/product
ids are also used for the DIGIVOX_AD. This may be a clone of the same
product. Explanatory text has been added prior to the hask look-up in
anticipation that it may help others.
The following has been tested to work:
Analogue TV (PAL-I)
Composite In
DVB-T (UK Crystal Palace)
USB AUDIO
The following has not been tested but probably works:
S-Video In
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes auto gain functional on 04fc:0561.
Signed-off-by: Shane <gnome42@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a buffer overflow in drivers/media/video/uvc/uvc_ctrl.c:
INFO: 0xf2c5ce08-0xf2c5ce0b. First byte 0xa1 instead of 0xcc
INFO: Allocated in uvc_query_v4l2_ctrl+0x3c/0x239 [uvcvideo] age=13 cpu=1 pid=4975
...
A fixed size 8-byte buffer is allocated, and a variable size field is read
into it; there is no particular bound on the size of the field (it is
dependent on hardware and configuration) and it can overflow [also
verified by inserting printk's.]
The patch attempts to size the buffer to the correctly.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The array size of 'shadow' still needs to be fixed in order to not overflow when reading register 0x00.
Thanks to Oliver Endriss for pointing that out.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Different backends have different input busses (saa7146, flexcop).
To reflect that a config-option to the s5h1420-driver was added which makes
the output mode selectable.
Furthermore the s5h1420-driver is now doing the same i2c-method as it was done
before adding support for other i2c-users.
This patch needs to go into the current release of the kernel, as this driver
is currently broken.
(Thanks to Eberhard Kaltenhaeuser for helping out to debug this issue.)
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions dvb_dmxdev_section_callback, dvb_dmxdev_ts_callback,
dvb_dmx_swfilter_packet, dvb_dmx_swfilter_packets, dvb_dmx_swfilter and
dvb_dmx_swfilter_204 may be called from both interrupt and process
context. Therefore they need to be protected by spin_lock_irqsave()
instead of spin_lock().
This fixes a deadlock discovered by lockdep.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2040:5510 is the same hardware as 2040:5500
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AMD ATI TV Wonder 600 has an XC3028L and *not* an XC3028, so we need to
load the proper firmware to prevent the device from overheating.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zr36067 driver is improperly declaring pixel format RGBP twice,
once as "16-bit RGB LE" and once as "16-bit RGB BE". The latter is
actually RGBR. Fix the code to properly map both pixel formats.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
sparc32 allmodconfig:
drivers/media/video/cafe_ccic.c: In function 'cafe_setup_siobuf':
drivers/media/video/cafe_ccic.c:1192: error: implicit declaration of function 'PAGE_ALIGN'
drivers/media/video/cafe_ccic.c: At top level:
drivers/media/video/cafe_ccic.c:1430: error: variable 'cafe_v4l_vm_ops' has initializer but incomplete type
drivers/media/video/cafe_ccic.c:1431: error: unknown field 'open' specified in initializer
drivers/media/video/cafe_ccic.c:1431: warning: excess elements in struct initializer
drivers/media/video/cafe_ccic.c:1431: warning: (near initialization for 'cafe_v4l_vm_ops')
drivers/media/video/cafe_ccic.c:1432: error: unknown field 'close' specified in initializer
drivers/media/video/cafe_ccic.c:1433: warning: excess elements in struct initializer
drivers/media/video/cafe_ccic.c:1433: warning: (near initialization for 'cafe_v4l_vm_ops')
drivers/media/video/cafe_ccic.c: In function 'cafe_v4l_mmap':
drivers/media/video/cafe_ccic.c:1444: error: 'VM_WRITE' undeclared (first use in this function)
drivers/media/video/cafe_ccic.c:1444: error: (Each undeclared identifier is reported only once
drivers/media/video/cafe_ccic.c:1444: error: for each function it appears in.)
drivers/media/video/cafe_ccic.c:1444: error: 'VM_SHARED' undeclared (first use in this function)
drivers/media/video/cafe_ccic.c:1461: error: 'VM_DONTEXPAND' undeclared (first use in this function)
This build breakage is caused by some header file shuffle in linux-next. But
I suggest that this patch be merged ahead of linux-next to avoid bisection
breakage.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zr36067 driver should return the actual bytes-per-line value when
queried with ioctl VIDIOC_G_FMT, instead of 0. Otherwise user-space
applications can get confused.
Likewise, with ioctl VIDIOC_S_FMT, we are supposed to fill the
bytes-per-line value. And we shouldn't fail if the caller sets the
initial value to something different from 0. This is perfectly valid
for applications to pre-fill this field with the value they expect.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restore the default pixel format to YUYV as it used to be before
kernel 2.6.23. It was accidentally changed to BGR3 by commit
603d6f2c8f.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following crash in the bttv driver:
BUG: unable to handle kernel NULL pointer dereference at 000000000000036c
IP: [<ffffffffa037860a>] radio_open+0x3a/0x170 [bttv]
This happens because radio_open assumes that all present bttv devices
have a radio function. If a bttv device without radio and one with
radio are installed on the same system, and the one without radio is
registered first, then radio_open checks for the radio device number
of a bttv device that has no radio function, and this breaks. All we
have to do to fix it is to skip bttv devices without a radio function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
