Implement support for HW scheduled scan. The mac80211 code doesn't perform
scheduled scans itself, but calls the driver to start and stop scheduled
scans.
This patch also creates a trace event class to be used by drv_hw_scan
and the new drv_sched_scan_start and drv_sched_stop functions, in
order to avoid duplicate code.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions drv_add_interface() and drv_remove_interface() print out
the same values in the traces. Combine the traces of these two
functions into one event class to remove some duplicate code.
Also add a new class for functions drv_set_frag_threshold() and
drv_set_rts_threshold().
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).
Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a new API for setting a TX rate mask in
drivers that have rate control in either the firmware or hardware.
This can be used for various purposes, for example, masking out the
11b rates in P2P operation.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a highly noisy environment, the tx rate of the driver drops and
the application slows down since it has not yet received ACKs for
the frames already queued in the hardware. Since this ACK may take
more than 100ms, stopping the dev queues for entering PS at this
stage breaks applications, WMM test cases in my testing.
If there are frames already pending in the tx queue, postponing the
PS logic helps to avoid redundant queue stops. When power save is
enabled by default and in a noisy environment, this API certainly
helps in improving the average throughput.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For devices supported by iwlwifi sometimes
off-channel transmissions need to be handled
by the device completely. To support this
mac80211 needs to pass the frame directly
to the driver and not through the TX path
as the driver needs the frame and channel
information at the same time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For events that include only the local struct as
their parameter, we can use DECLARE_EVENT_CLASS
and save quite some binary size across segments
as well lines of code.
text data bss dec hex filename
375745 19296 916 395957 60ab5 mac80211.ko.before
367473 17888 916 386277 5e4e5 mac80211.ko.after
-8272 -1408 0 -9680 -25d0 delta
Some more tracepoints with identical arguments
could be combined like this but for now this is
the one that benefits most.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.
In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.
Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to support remain-on-channel
offload if they implement smarter timing or need
to use a device implementation like iwlwifi.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow antenna configuration by calling driver's function for it.
We disallow antenna configuration if the wiphy is already running, mainly to
make life easier for 802.11n drivers which need to recalculate HT capabilites.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to mac80211 for changing the interface
type even when the interface is UP, if the driver
supports it.
To achieve this
* add a new driver callback for switching,
* split some of the interface up/down code out
into new functions (do_open/do_stop), and
* maintain an own __SDATA_RUNNING bit that will
not be set during interface type, so that any
other code doesn't use the interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a circular locking dependency when configuring the
hardware ARP filters on association, occurring when flushing the mac80211
workqueue. This is what happens:
[ 92.026800] =======================================================
[ 92.030507] [ INFO: possible circular locking dependency detected ]
[ 92.030507] 2.6.34-04781-g2b2c009 #85
[ 92.030507] -------------------------------------------------------
[ 92.030507] modprobe/5225 is trying to acquire lock:
[ 92.030507] ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8105b5c0>] flush_workq
ueue+0x0/0xb0
[ 92.030507]
[ 92.030507] but task is already holding lock:
[ 92.030507] (rtnl_mutex){+.+.+.}, at: [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507]
[ 92.030507] which lock already depends on the new lock.
[ 92.030507]
[ 92.030507]
[ 92.030507] the existing dependency chain (in reverse order) is:
[ 92.030507]
[ 92.030507] -> #2 (rtnl_mutex){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff81341754>] mutex_lock_nested+0x44/0x300
[ 92.030507] [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507] [<ffffffffa022d47c>] ieee80211_assoc_done+0x6c/0xe0 [mac80211]
[ 92.030507] [<ffffffffa022f2ad>] ieee80211_work_work+0x31d/0x1280 [mac80211]
[ 92.030507] -> #1 ((&local->work_work)){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105a51a>] worker_thread+0x22a/0x370
[ 92.030507] [<ffffffff8105ecc6>] kthread+0x96/0xb0
[ 92.030507] [<ffffffff81003a94>] kernel_thread_helper+0x4/0x10
[ 92.030507]
[ 92.030507] -> #0 ((wiphy_name(local->hw.wiphy))){+.+.+.}:
[ 92.030507] [<ffffffff81075fdc>] __lock_acquire+0x1c0c/0x1d50
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105b60e>] flush_workqueue+0x4e/0xb0
[ 92.030507] [<ffffffffa023ff7b>] ieee80211_stop_device+0x2b/0xb0 [mac80211]
[ 92.030507] [<ffffffffa0231635>] ieee80211_stop+0x3e5/0x680 [mac80211]
The locking in this case is quite complex. Fix the problem by rewriting the
way the hardware ARP filter list is handled - i.e. make a copy of the address
list to the bss_conf struct, and provide that list to the hardware driver
when needed.
The current patch will enable filtering also in promiscuous mode. This may need
to be changed in the future.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, driver tracing is sometimes invoked
after and sometimes before the actual driver
callback. This is fine as long as the driver
has no tracing itself, but as soon as it does
it gets confusing.
To make traces containing such information
easier to read, introduce a return tracer in
mac80211 that essentially brackets any driver
tracing, and invoke the real trace before the
driver's callback, only showing the return
value, if any, afterwards.
Since tracing records the process, there's no
problem with overlapping calls if that should
happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.
The debugfs code I recently added got this wrong
as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware allow extended filtering of ARP frames not intended for
the host. To perform such filtering, the hardware needs to know the current
IP address(es) of the host, bound to its interface.
Add support for ARP filtering to mac80211 by adding a new op to the driver
interface, allowing to configure the current IP addresses. This op is called
upon association with the currently configured address(es), and when
associated whenever the IP address(es) change.
This patch adds configuration of IPv4 addresses only, as IPv6 addresses don't
need ARP filtering.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for offloading the channel switch
operation to devices that support such, typically
by having specific firmware API for it. The reasons
for this could be that the firmware provides better
timing or that regulatory enforcement done by the
device requires special handling of CSAs.
In order to allow drivers to specify the timing to
the device, the new channel_switch callback will
pass through the received frame's mactime, where
available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scanning, it is somewhat important to scan
on the correct virtual interface. All drivers
that currently implement hw_scan only support a
single virtual interface, but that may change
and then we'd want to be ready.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance tracing by adding tracing for a variety of
callbacks that the drivers call, and also for
internal calls (currently limited to queue status).
This can aid debugging what is going on in mac80211
in interaction with drivers, since we can now see
what drivers call and not just what mac80211 calls
in the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() driver operation is not currently used anywhere in mac80211
and there are no plans to use it in the not-so-near future. So it can go
without anyone missing it.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many drivers would like to sleep during station
addition and removal, and currently have a high
complexity there from not being able to.
This introduces two new callbacks sta_add() and
sta_remove() that drivers can implement instead
of using sta_notify() and that can sleep, and
the new sta_add() callback is also allowed to
fail.
The reason we didn't do this previously is that
the IBSS code wants to insert stations from the
RX path, which is a tasklet, so cannot sleep.
This patch will keep the station allocation in
that path, but moves adding the station to the
driver out of line. Since the addition can now
fail, we can have IBSS peer structs the driver
rejected -- in that case we still talk to the
station but never tell the driver about it in
the control.sta pointer. If there will ever be
a driver that has a low limit on the number of
stations and that cannot talk to any stations
that are not known to it, we need to do come up
with a new strategy of handling larger IBSSs,
maybe quicker expiry or rejecting peers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I got below kernel oops when I try to bring down the network interface if
ftrace is enabled. The root cause is drv_ampdu_action() is passed with a
NULL ssn pointer in the BA session tear down case. We need to check and
avoid dereferencing it in trace entry assignment.
BUG: unable to handle kernel NULL pointer dereference
Modules linked in: at (null)
IP: [<f98fe02a>] ftrace_raw_event_drv_ampdu_action+0x10a/0x160 [mac80211]
*pde = 00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[...]
Call Trace:
[<f98fdf20>] ? ftrace_raw_event_drv_ampdu_action+0x0/0x160 [mac80211]
[<f98dac4c>] ? __ieee80211_stop_rx_ba_session+0xfc/0x220 [mac80211]
[<f98d97fb>] ? ieee80211_sta_tear_down_BA_sessions+0x3b/0x50 [mac80211]
[<f98dc6f6>] ? ieee80211_set_disassoc+0xe6/0x230 [mac80211]
[<f98dc6ac>] ? ieee80211_set_disassoc+0x9c/0x230 [mac80211]
[<f98dcbb8>] ? ieee80211_mgd_deauth+0x158/0x170 [mac80211]
[<f98e4bdb>] ? ieee80211_deauth+0x1b/0x20 [mac80211]
[<f8987f49>] ? __cfg80211_mlme_deauth+0xe9/0x120 [cfg80211]
[<f898b870>] ? __cfg80211_disconnect+0x170/0x1d0 [cfg80211]
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a TKIP key is updated, we should pass the station
pointer instead of just the address, since drivers can
use that to store their own data. We also need to pass
the virtual interface pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 callback to driver set_coverage_class() sets slot time and ACK
timeout for given IEEE 802.11 coverage class. The callback is optional,
but it's essential for long distance links.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've long lacked a good confirmation that frames
have really gone out, e.g. before going off-channel
for a scan. Add a flush() operation that drivers
can implement to provide that confirmation, and use
it in a few places:
* before scanning sends the nullfunc frames
* after scanning sends the nullfunc frames, if any
* when going idle, to send any pending frames
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable spatial multiplexing in mac80211 by telling the
driver what to do and, where necessary, sending action
frames to the AP to update the requested SMPS mode.
Also includes a trivial implementation for hwsim that
just logs the requested mode.
For now, the userspace interface is in debugfs only,
and let you toggle the requested mode at any time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not all that useful to have the vif/sdata pointer,
we'd rather refer to the interfaces by their name.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For bluetooth 3, we will most likely not have
a netdev for a virtual interface (sdata), so
prepare for that by reducing the reliance on
having a netdev. This patch moves the name
and address fields into the sdata struct and
uses them from there all over. Some work is
needed to keep them sync'ed, but that's not
a lot of work and in slow paths anyway.
In doing so, this also reduces the number of
pointer dereferences in many places, because
of things like sdata->dev->dev_addr becoming
sdata->vif.addr.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable logging of more configuration data when tracing
is enabled. Except for the channel frequency this is
only useful with the binary trace format, but that can
be recorded and replayed with trace-cmd and I will be
working on a plugin that reports all the information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following errors:
driver-trace.h:148:1: error: cannot size expression
driver-trace.h:148:1: error: cannot size expression
[...]
driver-trace.h:222:1: error: cannot size expression
driver-trace.h:71:1: error: incompatible types for operation (<)
driver-trace.h:71:1: left side has type void *<noident>
driver-trace.h:71:1: right side has type int
driver-trace.h:99:1: error: incompatible types for operation (<)
driver-trace.h:99:1: left side has type void *<noident>
driver-trace.h:99:1: right side has type int
driver-trace.h:148:1: error: incompatible types for operation (<)
driver-trace.h:148:1: left side has type void *<noident>
driver-trace.h:148:1: right side has type int
driver-trace.h:222:1: error: cannot size expression
driver-trace.h:248:1: error: incompatible types for operation (<)
driver-trace.h:248:1: left side has type void *<noident>
driver-trace.h:248:1: right side has type int
driver-trace.h:446:1: error: incompatible types for operation (<)
driver-trace.h:446:1: left side has type void *<noident>
driver-trace.h:446:1: right side has type int
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 use the event tracing framework
to log all operations as given to the driver. This
will need to be extended with more information, but
as a start it should be good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
