To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.
This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Lothar Wassmann
The patch makes sure, that the ouptut functions of pins are restored
before restoring the Alternat Function settings, preventing pins from
being intermediately configured for undefined or unwanted alternate
functions.
Here is the original comment:
I've got a PXA270 system that uses GPIO80 as nCS4. This system did
hang on resume. Digging into the problem I found that the processor
stalled immediately when restoring the GAFR2_U register which restored
the alternate function for GPIO80. Since the GPDR registers were
restored after the GAFR registers, the offending GPIO was configured
as input at this point.
Thus the alternate function that was in effect after restoring the
GAFR was in fact the input function "MBREQ" instead of the output
function "nCS4". The "PXA27x Processor Family Developer's Manual"
(Footnote in Table 6-1 on page 6-3) states that:
"The MBREQ alternate function must not be enabled until the PSSR[RDH]
bit field is cleared. For more details, see Table 3-15, "PSSR Bit
Definitions" on page 3-71."
There is another note in the Developer's Manual (chapter 24.4.2
"GPIO operation as Alternate Function" on page 24-4)
stating that:
"Configuring a GPIO for an alternate function that is not defined for
it causes unpredictable results."
Since some GPIOs have no input function defined, and to prevent
inadvertedly programming the MBREQ function on some pin, the GAFR
registers should be restored after the GPDR registers have been
restored.
Additional provisions have to be made when the MBREQ function is
actually required. The corresponding GAFR bits should not be restored
with the regular GAFR restore, but must be set only after the PSSR
bits have been cleared.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Akita requires inbuilt kernel i2c support for its GPIOs. Add this
requirement to Kconfig and update the defconfig to match.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add iWMMX Extentions for the pxa27x based Zaurus models and
fix a couple of minor mistakes in the PXA Kconfig file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
Fix an error in tosa.c after the platform device conversion.
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a driver for the extra GPIOs found on the Sharp SL-C1000 (Akita).
These GPIOs are found on a Maxim MAX7310 I2C i/o expander chip. A
generic GPIO driver for the MAX7310 was attempted but this mini
driver is a much simpler and much more effective solution avoiding
several issues and complexity the generic driver had (as discussed
on LKML).
The platform device is required so the device parent can be set
correctly which ensures the device is one of the last to suspend
and first to resume. Whilst the i2c suspend/resume calls can be
influenced, nothing guarantees this is easlier/later than the
subsystems the gpios are used on which are all independent of i2c
(sound, irda, video/backlight etc.).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a SharpSL PM device driver for the SL-Cxx00 machines.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a SharpSL PM device driver for the SL-C7x0 machines.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Updates to the SharpSL PM driver including cleanups from both
Pavel Machek and myself and updates after the platform device
changes to make it compile again.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add the core machine support for the Sharp SL-C1000 (Akita)
and enable the Kconfig selection for it.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Liam Girdwood
This patch allows users of the pxa SSP driver to register their own irq
handlers instead of using the default SSP handler. It also cleans up the
CKEN clock and irq detection as the values are now stored in a table.
This patch replaces 2845/1
Changes:-
o Added flags parameter to ssp_init()
o Added SSP_NO_IRQ flag to disable registering of ssp irq handler (for
drivers that want to register their own handler)
o Cleaned up clock and irq detection, values are now stored in table.
o Added build changes to allow other drivers (e.g audio) to select the
ssp driver.
o corgi_ssp.c changed to use new interface.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch adds a power and battery management core driver which with
the addition of the right device files, supports the c7x0 and cxx00
series of Sharp Zaurus handhelds.
The driver is complex for several reasons. Battery charging is manually
monitored and controlled. When suspended, the device needs to
periodically partially resume, check the charging status and then
re-suspend. It does without bothering the higher linux layers as
a full resume and re-suspend is unnecessary. The code is carefully
written to avoid interrupts or calling code outside the module under
these circumstances. It also vets the various wake up sources and
monitors the device's power situation.
Hooks to limit the backlight intensity and to notify the battery
monitoring code of backlight events are connected/added as the
backlight is one of the biggest users of power on the device.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Nicolas Pitre
Make it completely deterministic and leave nothing to chance
(even if it had at worst 0.001% probability of failing).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch updates the tosa machine to use the new SharpSL PCMCIA layer introduced with Patch #3093/1
Depends on #3093/1
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The Sharp SL-Cxx00 models have a combined power control for the SD
and CF slot 0. This patch adds hooks to the scoop driver to allow
machines to provide a custom control function for this and such a
function is added for spitz/akita/borzoi.
It also moves the gpio init code into the machine files as this
is machine dependent and differs between some models. A couple of
warnings when compiling for collie are also fixed.
Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch adds MMC, IRDA and UDC support to the Sharp SL-6000x device. Also it adds a platform device for the keyboard driver.
Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Update the PXA pm.c file to allow machines (such as the Sharp
Zaurus) to override the standard pm functions but reuse/wrap them
where needed.
The init call is made slightly earlier to give machine code an init
level to override them in removing any race.
Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch adds basic machine support for the Sharp SL-6000x (Tosa) PDAs.
Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add platform devices for flash to Lubbock and Mainstone board files.
Once in place, the two existing mtd map drivers for the boards will be
converted to use a single pxa2xx map driver in the linux-mtd tree.
Take 4: flash_platform_data .map_name vs. .name cleaned up, resync with
merged irda patch context.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
Lubbock updates:
* Provide an address for the SMC91x chip that doesn't generate
a boot-time warning (matching the EEPROM).
* Update MMC support to (a) detect card insert/remove, and
(b) report the readonly switch setting for SD cards.
Previously, MMC/SD cards had to be present at boot time else they
couldn't be detected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Add spitz irda platform support
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add corgi irda platform support
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add poodle irda platform support
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Nicolas Pitre
This is the PXA2xx common IRDA driver, plus platform support
for Lubbock and Mainstone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add symbols for PXA2xx PWRMODE register M field that selects low-power
mode, replace unadorned constants. Honor power mode parameter of
pxa_cpu_suspend(mode), no longer force to 3 (sleep). Full Deep Sleep
low-power mode support for PXA27x is pending generic PM interfaces to
select more than 2 suspend-to-RAM-style power modes, but this is
expected soon. This can be hardcoded in the meantime by replacing the
pxa_cpu_suspend() parameter value. From David Burrage and Todd Poynor.
Try #2 removes one of the register copies and moves the code to save the
pxa_cpu_suspend parameter to immediately surround the call that requires
the parameter value be preserved.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ian Campbell
As noted by Uli Luckas in the comments of 3025 there is a typo in the i2s platform device. The i2s platform device refers to the i2c resources.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
PXA map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes compile problem when CONFIG_FB_PXA is not set.
LD .tmp_vmlinux1
arch/arm/mach-pxa/built-in.o(.text+0x1d74): In function
`spitz_get_hsync_len':
: undefined reference to `pxafb_get_hsync_time'
make: *** [.tmp_vmlinux1] Error 1
3.46user 0.46system 5.10 (0m5.106s) elapsed 77.01%CPU
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Matt Reimer
Adds an I2S platform_device for PXA. I2S is used to interface
with sound chips on systems like iPAQ h1910/h2200/hx4700 and
Asus 716.
Signed-off-by: mreimer@vpop.net
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Remove a couple of lines of accidently added code causing compile
errors.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Update corgi_lcd to use bus_find_device to locate the pxafb device
hence fixing a compile error.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a function to allow machines to set the parent of the pxa
framebuffer device. This means the power up/down sequence can be
controlled where required by the machine.
Update spitz to use the new function, fixing a compile error.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a missing include from corgi.c
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix
arch/arm/mach-pxa/generic.c:242: warning: 'struct i2c_pxa_platform_data' declared inside parameter list
caused by missing asm/arch/i2c.h include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch adds MMC and UDC support to the PXA Poodle platform.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch cleans up the PXA Poodle platform code removing an unneeded
static iomap. It also corrects errors in the platform header file and
adds a missing GPIO define.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch cleans up the PXA Corgi platform code removing an unneeded
static iomap, an unneeded function and some debug messages.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
