On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all zero page implementations use empty_zero_page global pointer so
let's substitute empty_zero_page occurence with helper ZERO_PAGE(0).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Link: https://lore.kernel.org/r/20221018215755.33566-2-giulio.benetti@benettiengineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl_spi_cpm_free() function does not make the same
checks as the error path in fsl_spi_cpm_init() leading
to crashes on error.
Cc: Fabio Estevam <festevam@gmail.com>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191113014442.12100-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-37-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
devm_ioremap_resource() doesn't return NULL but an ERR_PTR on error.
Reported-by: Jonas Gorsky <jogo@openwrt.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
On CPM2, the SPI parameter RAM is dynamically allocated in the
dualport RAM whereas in CPM1, it is statically allocated to a default
address with capability to relocate it somewhere else via the use of
CPM micropatch. The address of the parameter RAM is given by the boot
loader and expected to be mapped via devm_ioremap_resource()
In the current implementation, in function fsl_spi_cpm_get_pram()
there is a confusion between the SPI_BASE register and the base of the
SPI parameter RAM. Fortunatly, it is working properly with MPC866 and
MPC885 because they do set SPI_BASE, but on MPC860 and other old
MPC8xx that doesn't set SPI_BASE, pram_ofs is not properly set.
Also, the parameter RAM is not properly mapped with
devm_ioremap_resource() as it should but still gets accessible by
chance through the full RAM which is mapped from somewhere else.
This patch applies to the SPI driver the same principle as for the
CPM UART: when the CPM is of type CPM1, we simply do an
devm_ioremap_resource() of the area provided via the device tree.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
On CPM1, when the SPI parameter RAM is relocated to somewhere else than the
default location, in accordance with freescale documentation
(refer micropatch SPI application note EB662), init RX/TX params command shall
not be used because it doesn't take into account the new location, and
overwrites data that is in original location of SPI param ram at addresses
SCC2 param base + (u32*)0x88 (u16*)0x90 (u32*)0x98 (u16*)0xA0, hence breaking
activity on SCC2 if SCC2 is used in a mode like QMC for instance.
Therefore, the action shall be done manually as described by freescale and as
was already partly done by the driver.
Reported-by: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sort all the include headers alphabetically for the freescale
spi drivers. If the inlcude headers sorted out of order, maybe
the best logical choice is to append new ones after the exist
ones, while this may create a lot of potential for duplicates
and conflicts for each diffenent changes will add new headers
in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
This makes the spi-fsl-spi driver usable in CPU mode outside of an FSL_SOC and
even an powerpc environment by moving CPM mode functionality to a separate file
that is only compiled and linked in an FSL_SOC environment and adding some
ifdefs to hide types and functions or provide alternatives.
For devicetree probing a "clock-frequency" property is used for clock frequency
instead of calls to FSL_SOC-specific functions.
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Christophe Leroy
Giulio Benetti
Gustavo A. R. Silva
Linus Walleij
YueHaibing
Thomas Gleixner
Zhao Qiang
Christophe Leroy
Esben Haabendal
Xiubo Li
Linus Torvalds
Jarkko Nikula
Rob Herring
Andreas Larsson